A close view of a gate photo eye sensor on a post with dust and a spider web across the lens.

San Antonio Automatic Gates: Why Your Gate Opener Stopped Working

When a gate opener quits, the fix is often simpler than you'd think. This guide from San Antonio Automatic Gates walks through the most common reasons a gate opener stops working, what you can safely check yourself, and when it's time to call for repair.

Monday to Saturday, 7:00 AM to 7:00 PM

Get a Free Gate Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

Last updated: November 19, 2026

Safety first

Before you check anything, keep people, pets, and cars away from the gate. A gate can start moving when a fault clears. Don't put your hands near hinges, rollers, or the opener arm while power is on. If you need to open the gate by hand, use the opener's manual release, and turn off power at the breaker before opening the control box.

What is your gate doing?

Gate opener problems and what to check
What the gate is doingWhat to check first
Nothing at allBreaker, outlet, transformer, battery, solar panel
Hums but won't moveRelease the gate and see if it moves freely by hand
Opens but won't closePhoto eyes blocked or out of line, stuck safety edge
Starts, then reversesSomething in the way, a dragging gate, or a tripped sensor
Stops partwayLow battery, a binding hinge or roller, limits out of adjustment
Remote doesn't work, keypad doesRemote battery or remote programming
Nothing opens it, but the board has lightsReceiver, keypad wiring, or the board itself
Opens by itselfExit sensor, loop, or a stuck button or keypad

Check the power

No power is the most common reason a gate does nothing at all.

  • Check the breaker for the gate circuit and reset it if it tripped.
  • If the opener plugs into an outlet, check for a tripped GFCI outlet.
  • Look for lights on the control board. No lights usually means no power.
  • On a solar gate, check that the panel is clean and in the sun. New shade from a tree can starve the battery.
  • If the gate stopped after a storm or power outage, the backup battery may be drained or the board may need a reset.

Check the battery

Most openers run off a battery that the house power or a solar panel keeps charged. Batteries wear out, and San Antonio heat wears them out faster. A dying battery can make a gate slow, stop halfway, or work only some of the time. If your battery is a few years old, that's a good suspect. We can test it and replace it.

Check the photo eyes and sensors

If the gate opens but won't close, or starts closing and reverses, the safety sensors are the usual cause. That's them doing their job.

  1. Look for anything between the photo eyes: plants, trash cans, toys, or a parked car.
  2. Wipe both lenses with a soft cloth. Dust, pollen, and spider webs can block them.
  3. Check that the sensors still point at each other. A bump from a mower can knock one out of line. Many have a small light that shows when they're lined up.
  4. Check safety edges on the gate for damage or anything pressing on them.

Never disconnect or bypass safety sensors to make the gate close. They're there to keep someone from getting hurt.

Check the gate itself

Pull the manual release and move the gate by hand. It should swing or roll smoothly through its full travel. If it drags, sticks, or is hard to push, the opener isn't the problem. The gate is. Common causes:

  • A sagging gate dragging on the ground
  • A leaning hinge post
  • Dry or worn hinges or rollers
  • Debris in a slide gate's track
  • A bent gate frame

A gate that drags makes the opener work harder, overheat, and trip its safety stop. Fixing the gate often fixes the opener.

Check the remotes and keypad

If the gate works from one remote but not another, replace the battery in the one that doesn't work. If no remote works but the keypad does, the receiver may have lost its programming or failed. If the keypad stopped taking codes, check for damage, water, or ants inside it. Write down any error code on the control board. It tells us a lot.

When should you call?

Call us when:

  • The power and battery are good but the gate still won't run
  • The motor hums or clicks but won't move a gate that moves freely by hand
  • The control board shows an error code you can't clear
  • There's damage from a storm, a car, or water
  • The gate makes grinding or popping sounds
  • You've checked the sensors and the gate still won't close

Tell us what you checked and what you found. It helps us bring the right parts the first time. See gate opener repair.

Angi puts the average automatic gate repair at about $900, with most repairs between $550 and $1,500, and lists remote or keypad fixes at $75 to $300.

Source: Angi, Automatic Gate Repair Cost

Those are national numbers, not our prices. Many repairs, like a battery or sensor, cost far less than a new opener.

Gate opener troubleshooting FAQs

Almost always the safety sensors. Something is blocking them, they're dirty, or they're out of line.

Still stuck?

Call us. We'll find out why and get your gate moving again.

Get a Free Gate Quote

By submitting, you agree to our Privacy Policy and Terms of Service.

Call NowFree Quote